How to Clean Your Tankless Water Heater

Over time, a tankless water heater may accumulate mineral build up which can erode the walls inside your tank’s heating chamber. To properly maintain and clean your tankless water heater, it’s important to flush those mineral deposits at least once a year. Follow this simple 12-step process to ensure optimal tankless water heater performance and efficiency. Please read all of the instructions before beginning, as you’ll want to have all of the necessary supplies ready for the process. If you’re not comfortable doing this process yourself, please contact us and schedule an appointment with one of our professionally trained service technicians.


1. Turn off the power source for your tankless water heater.



  • Shut off the main gas or turn off the circuit breaker for electrical devices.


2. Close (turn off) the three water valves attached to your tankless water heater.



  • This prevents cold water from flowing into the water heater and hot water from coming out during the cleaning process.

  • The water valves consist of a cold water valve (colored blue), a hot water valve (colored red) and a main valve that runs the water into your home.


3. Remove the purge port valve caps slowly from the purge valves located on each of the cold and hot water valves.



  • The purge valves have small handles that resemble the letter "T."

  • This procedure is done to relieve any pressure that has built inside the valves and will prevent excess hot water from shooting out during the cleaning process.

  • There may be pressure when removing the purge port valve caps, so it’s vital to confirm the hot water valve is completely shut off for your safety.

  • Handle each cap carefully so the rubber sealing discs stay in place. These are needed for your valves to function properly.


4. Attach hosing lines to each of the three valves.



  • If the manufacturer of your tankless water heater did not provide hosing lines, they are available at any home repair store that sells water heaters. The hosing lines must be long enough to reach between the water heater and a bucket.

  • Consult the manual provided by the tankless water heater manufacturer or contact the manufacturer directly for exact instructions regarding this procedure.

  • In some cases, this procedure may require you to use a sump pump and connect hoses to discharge and flush water from the tankless water heater cold and hot water valves.


5. Open the purge port valves by twisting them perpendicular to the position of the cold and hot valves.


6. Use 2.5 gallons (9.46 liters) of undiluted white vinegar to clean your tankless water heater. Never use chemical solutions of any kind.



  • Since your home’s drinking and bathing water mostly likely flows through your tankless water heater, using chemical cleaning solutions could be extremely harmful to your health.


7. Follow the instructions included in your manufacturer’s manual to perform the flushing and draining procedure.



  • This procedure may take up to 45 minutes.


8. Once the flushing process is complete, close the purge port valves by twisting the T-shaped handles.


9. Disconnect and remove the hosing lines from each valve.


10. Replace the purge port valve caps onto the purge valves.



  • Tighten the caps completely and firmly. However, take care not to over-tighten or break the rubber sealing discs inside the caps.


11. Refer to the manufacturer’s manual for exact instructions on how to safely restart your water heater.



  • This may require you to rotate and open the cold and hot water valves so they are parallel to the position of the main valve.


12. Choose a sink tap inside and turn on the hot water slowly to allow the air to pass through the pipe.



  • Continue to run the water until it runs steadily without air escaping (you may recognize this by a slight sputtering sound). .

  • It may take to 2 or 3 minutes for all of the air pockets to escape.


Contact CES at 800-874-1975 or complete the form below.


If you have questions about your service or products we offer, please email info@combinedenergyservices.com Do not leave a service or product question in the comments.






















































































































































Request *








































 





Combined Energy Services Employee

Combined Energy Services

Service Locations

New York Counties
Columbia, Delaware, Dutchess, Greene, Orange, Putnam, Rockland, Sullivan, & Ulster

 

Pennsylvania Counties
Monroe, Pike & Wayne

 

New Jersey Counties
Bergen, Hunterdon, Morris, Passaic, Somerset, Sussex, & Warren

Our Locations

Monticello, NY

216 East Broadway
Monticello, NY 12701
Phone: (845) 794-1210
Fax: (845) 794-0238

Dingmans Ferry, PA

1483 Route 739
Dingmans Ferry, PA 18328
Phone: (570) 828-1700
Fax: (570) 828-2523

Andover, NJ

430 U.S. 206
Newton, NJ 07860
Phone: (973) 948-0090
Fax: (973) 383-0161

Satellite Fuel Storage Facilities

Thompsonville, NY 
Liberty, NY 
Saugerties, NY

New Hampton, NY

1 Musket Ct.
New Hampton, NY 10958
Phone: (845) 294-4343 / (845) 343-5353
Fax: (845) 606-8026
All Gas Welding: (845) 294-7771

Kerhonkson, NY

6525 U.S. 209
Kerhonkson, NY 12446
(corner Rt 209 & Rt. 44/55)
Phone: (845) 647-6226
Fax: (845) 626-1290

West Nyack, NY

155 South Route 303
West Nyack, NY 10994
Phone: (845) 535-5340
Fax: (845) 535-4491

 

Bethel, NY 
Dingmans Ferry, PA

Combined Energy Services · 216 East Broadway · Monticello · NY 12701

Copyright © 2024 · Powered by LOCALiQ